Shirly B44' Irwin 44 1987

Hull

Rudder

Remove the fiberglass shell and foam. Cut 5/8 steel flag off, have new rudder 1”1/8” S/S shaft

cut key way, weld flag onto rudder shaft ( the Half inch by 10 in x 2 ft by half inch steel plate),

sand blast flag and paint epoxy, glass flag and Fill with polyurethane foam trim and glass shaft

assembly to shell other half. Close with glass , Seal shaft exit from fiberglass shell. with 3M

5200 and a ¼ in rabbit

Install new rudder stuffing box , new Edison Pull Pull steering cables and 6 by 19 S/S steering

wire rope, install greased cups on cable, new, new bicycle chain inside the binnacle to steering

sprocket Cumming off the wheel, weld steering wheel 2 spokes broken, make and install High

Molecular Weight Plastic bearing for bottom bearing of rudder

• Yanmar 4JH2-UTE turbo diesel complete rebuild top and bottom end complete in-frame rebuild

including cylinder sleeves, built injectors, fuel injection pump rebuilt, new engine mounts, new

bearing in reverse gear, 90 amp alternator, rebuild engine electrical control's and trouble

warning system, there is a problem with the buzzer mechanical pressure gauge on the engine

needs replacing forward and reverse cable have new one on boat. Have sound insulation many

many pieces in some large pieces for engine compartment. They are in Storage.

• All hoses in engine compartment replaced except final engine hose exhaust
• Fuel distribution system upgraded to fuel pump, new three-way valves replace original filters

with Racore 20/10pm size need some work still

• New collapsible entry ladder for sugar scoop, currently stored on deck

• New cabinet hinges uninstall, many of the cabinet doors are uninstalled and drawer sets. They

are in storage.

• Repair Salon table Supports

Electrical

• Have cob LEDs and blue LEDs and 3 position switches to convert all interior lights for night

time and night running

• Balmar fridge freezer install new electronic controller, Buck Boost soft starter, Led temp display

and control, permanently installed high and low pressure refrigerant gauges all in the cabinetry.

• Have new compressor and cold plate uninstalled.
• Have replacement AC unit not installed currently in storage
• I have new three bank battery charger upgrade from analog charger
• Install bilge pump with foot switch in main bilge there is room for another one and already and

piped for overboard

• 2 new magnetic type air-con sea water circulating pumps one for fwd and aft for redundancy

(can run both on one)

• Furuno weather fax
• Generator is shot 8Kw unrecoverable
• All new anti siphons for gen and mane
• New forward reverse gear hand control on binnacle for engine
• Replace both anti-siphon elbows on generator and Main engine fabricate P tube anti siphon
• collector from stainless steel installed in the starboard Scupper drain

• New Brooks and Gatehouse Vulcan chart plotter with 50/200 Hz depth transducer
• 2 new low profile Bronze sea strainers, all through hull fittings and valves
• IInstall B&G Vulcan chart plotter and 50/200 MHG t12vransducer
• Commercial cloth 3 inch ducting new s/s vent aft
• Fabricate shelving in forward head Start turning into storage don't need two heads on a 44 ft

boat

• New bottom paint new prop speed
• 15 hp mercury outboard needs carburetor kit
• Replacement cushion covers for all salon cushions made from Ultrasuede Uninstalled

Evernote

• Dinghy anchor
• Upgraded mainsheet traveler with cam cleats needs bending to a curve
• There’s quite a bit of running rigging shackles, wire and electrical parts, plumbing, bilge pumps,

rigging sewing kit some tools, extra parts stored below

All Items on this List are on the Vessel excluding More Solar panels and New Batteries

• Finish battery cables
• drain inn forward head

● Pie eye forward head

● crack in keel haul out

Install more solar panels on radar arch

● paint radar arch

● install access panels in aluminum fuel tanks

● remove the starboard fuel tank out remove the water tank soft patch and

Reinstall

● Install vacuum style mechanical water tank gauge

● Finish Mebay generator controller

● Pie eye on gen engine trunk for gen dipstick

● Pie eye on gen engine trunk for engine dipstick

Install batteries in aft cabin under bunk forward make access for prop skeg and

bilge service

● Reseal mast boot

● Install second 4 to 1 purchase on boom Vang

● Install cooking strap

Oil change both gen and mane 30 Hr break in after full rebuild

● reset valves 30 Hr break in after full rebuild

● some wood work I aft cabin

● some woodwork in aft head

● install new shower head in aft head

new mirror in aft head vanity storage

● finish and install Browny dive compressor

● install commercial gyro compass

● Install new toilet in aft Head

● install fiberglass original strength members on gen engine trunk

Install flooring Pergo style in salon

● make 4 s/s deck light bezels

● build a Spirulina sun manufacture class tube install on arch

● The sugar scoop needs fiberglass repair there's a three-quarter inch

piece of wood covering the deck with 5200 the fiberglass underneath needs

repair I have a sheet of Coosa board, glass, resin

● The main sale boom Beckett on the end for the main sheet is broken I'm

using a lifting strap currently

● Of the halyards run to the mast need to be run into the cockpit for single-

handing

● I still have all the interior Cabinetry including the drawers in storage I can

put them back or I was thinking about converting some of the cabinet space into

single doors and not Barbie size drawers

● install a macerator for the aft black water tank To facilitate overboard

pumping

● Need to reinstall The bottom of the engine trunk forward under the

companionway stops it was cut out to put the engine in

● Need to install hand bilge pump on engine trunk port side forward

● Need to send weather fax back to Max Marine to get checked out with the

antenna also the SSB

● I would like to install a radar on the afterche digital to match B&G

Electronics

● Air ride vibration mounts for vibration under aft aircon for vibration

Have on boat;

• Mast self ascender Bossons chair new
• Bossons chair new
• Balmar refrigeration controller and electronic temp control for Refrigeration
• fresh water pump
• epoxy and cloth
• Spreader led lights
• Tools electrical repair parts full set electrical connectors
• repair parts for freshwater plumbing piping
• full bosons ditty bag for sail repair
• Reaching pole need some hardware
• 175’ of anchor
• 1500 watt inverter
• 400 watt inverter
• cooking and utensils
• Wiss 30 inch s/s rigging cutter
• full set of mechanics tools
• First aid extensive
• day night light activated anchor light
• 3 new halyards
• 2 new sheet sets
• new van line
• new lazy jacks
• mane sail sun cover
• New to boat 80 percent life mane sail
• Battery charging switch modules from combined charge sources (instead of Diodes or automatic
• combiners)
• Dive equipment
• S/s dive ladder mounted on sugar scoop

Listing MLS by Yachtr.com